aluminum electrolytic capacitors 1 voltage capacitance 105 c marking 105 c marking ( 3 to 8 5.4 ) ( 8 10, 10 10 ) n2p 10 16v plastic platform 0.3 max. l (l 0.3) +0.1 ?.2 d 0.5 b 0.2 c 0.2 0.5 max. a 0.2 a 0.2 e h h positive negative 1 voltage capacitance trade mark lot no. n2p 100 35v plastic platform 0.3 max. l 0.5 pressure relief vent 1. voltage mark for 6.3v is 6v . in case of marking for 3 units, ??for rated voltage is omitted. 2. in case of marking for 3 units. lot no is expressed by a digit (month code). 3 apply to 6.3 5.8, 6.3 7.7 d 0.5 b 0.2 c 0.2 0.5 max. a 0.2 a 0.2 e positive negative lot no. 2 3 u 1 w 2 t 3 1 4 c 5 1 6 0 7 0 8 m 9 c 10 l 11 1 12 g 13 b 14 configuration package code size code capacitance tolerance ( 20%) rated capacitance (10 f) rated voltage (16v) series name type d 3 4 to 10 code 2 1 d 3 to 8 (5.4l) 6.3 to 10 (l 5.8) code gb gs d 3 to 8 (l 7.7) 8 to 10 (l = 10) code cl nl a b c e l h 3 5.4 1.5 3.3 3.3 0.8 5.4 0.5 to 0.8 4 5.4 1.8 4.3 4.3 1.0 5.4 0.5 to 0.8 5 5.4 2.1 5.3 5.3 1.3 5.4 0.5 to 0.8 6.3 5.4 2.4 6.6 6.6 2.2 5.4 0.5 to 0.8 6.3 5.8 2.4 6.6 6.6 2.2 5.8 0.5 to 0.8 6.3 7.7 2.4 6.6 6.6 2.2 7.7 0.5 to 0.8 8 5.4 3.3 8.3 8.3 2.3 5.4 0.5 to 0.8 8 10 2.9 8.3 8.3 3.1 10 0.8 to 1.1 10 10 3.2 10.3 10.3 4.5 10 0.8 to 1.1 d l (mm) wt series chip type, wide temperature range chip type operating over wide temperature range of to 55 to +105 c . designed for surface mounting on high density pc board. applicable to automatic mounting machine fed with carrier tape. compliant to the rohs directive (2002/95/ec). chip type type numbering system (example : 16v 10 f) specifications category temperature range rated voltage range rated capacitance range capacitance tolerance leakage current tangent of loss angle (tan ) stability at low temperature endurance shelf life marking performance characteristics item 55 to +105 c 4 to 50v 0.1 to 1500f 20% at 120hz, 20 c after 2 minutes' application of rated voltage, leakage current is not more than 0.01cv or 3 (a) , whichever is greater. black print on the case top. measurement frequency : 120hz, temperature : 20 c measurement frequency : 120hz the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 1000 hours at 105 c. after storing the capacitors under no load at 105 c for 1000 hours and then performing voltage treatment based on jis c 5101-4 clause 4.1 at 20 c, they shall meet the specified values for the endurance characteristics listed above. resistance to soldering heat the capacitors are kept on a hot plate for 30 seconds, which is maintained at 250 c. the capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20 c. rated voltage (v) tan (max.) 4 0.40 6.3 0.30 10 0.24 16 0.20 25 0.16 35 0.14 50 0.14 z 25 c / z+20 c z 40 c / z+20 c rated voltage (v) impedance ratio zt / z20 (max.) 4 7 15 6.3 4 8 10 3 8 16 2 4 25 2 4 35 2 3 50 2 3 wt capacitance change leakage current tan within 25% of the initial capacitance value for capacitors of 3mm unit, and 16v or less . within 20% of the initial capacitance value for capacitors of 25v or more. 200% or less than the initial specified value less than or equal to the initial specified value capacitance change leakage current tan within 10% of the initial capacitance value less than or equal to the initial specified value less than or equal to the initial specified value dimension table in next page. smaller zt low impedance wf long life ut wz high temperature reflow cat.8100y
aluminum electrolytic capacitors wt series dimensions 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 150 220 330 470 680 1000 1500 0r1 r22 r33 r47 010 2r2 3r3 4r7 100 220 330 470 101 151 221 331 471 681 102 152 4 4 0j 6.3 1a 10 1c 16 1e 25 1v 35 1h 50 4 c 120hz ( ) is also available with
|
